Ten top tips for longevity

On a bike that’s used every day for commuting a certain amount of wear and tear is inevitable, but there’s a lot you can do to slow down the process – and most of these tips will not only save on maintenance costs, they’ll make the bike more efficient and pleasurable to ride too.

1. Keep your tyres inflated

Riding on soft tyres will cause the sidewalls to crack and split, and also makes punctures more likely. All inner tubes are slightly porous and go flat over time, so check your tyre pressures every week, and expect to pump them up at least monthly. Having a good full-size track pump at home or work really helps!

2. Wipe and lube the chain regularly

Every week or two, check to see if the chain seems dry or dirty. If so, lean the bike against a wall and give the chain a wipe with a rag whilst backpedalling, and then apply chain oil sparingly. Then once the oil has had a chance to soak down into all the cracks in the chain, give it a wipe again with a clean bit of rag to remove any surface oil. This way the chain will always be lubricated, but never too dirty or oily. Little and often is the key.

3. Lube your cables

On almost all modern bikes, there are slots in the cable guides on the frame to allow the cables to be removed for cleaning and oiling without having to fully disconnect them or use any tools at all. I suggest you pop the gear and brake cables out every few months and lube them with a little normal chain oil. This not only stops them rusting, it also prevents the plastic liners from getting worn out, and makes the brakes and gears feel nice and slick to use!

4. Lube your mechs

Even easier than lubing the cables – simply put a drip of oil on each pivot of the front and rear derailleurs (mechs). What we’re aiming for is to lube every moving part of both mechs, so if in doubt just watch what moves when you change gear and then oil it. Change gear a few times afterwards to allow the oil to soak in, then wipe down the mech with a rag to clean off any excess oil. This will prevent the mechs from corroding, and will slow the rate of wear right down.

5. Check and adjust your brakes

Brake blocks wear out with use. They are cheap to replace, so no problems there. But if, as they wear, they come into contact with the tyres, very quickly a hole will be worn into the tyre sidewall, meaning that the tyre and probably the tube will have to be replaced. And if the brake blocks completely wear out, or pick up some gravel or debris, they can wear out the rim requiring a whole new wheel. So if you have normal rim brakes and they start making a funny noise, check it immediately (a squeak or squeal doesn’t matter, but a scraping or grinding noise definitely does!)

6. Fit mudguards

How does this effect the longevity of the bike? As well as protecting you from mud and water, mudguards will prevent the chain, gears and brakes from getting so dirty too. Less grit and water means less wear and corrosion, which the chain will definitely appreciate in the long term.

7. Get your hubs and headset serviced

Every year or two on more expensive bikes it makes sense to have your bike’s main bearing systems disassembled and re-greased instead of having to replace them when they rust or dry out, potentially at a cost of a couple of hundred pounds. Just give us a call if you’d like to book your bike in for a bearings service.

8. Don’t store your bike outside

Even the most expensive bikes have a steel chain and bearings which will rust if exposed to rain or moisture. Keeping your bike indoors if at all possible is ideal; if not then a shed or bike store is sufficient, or get a good quality bike cover as a bare minimum.

9. Don’t stomp on the pedals

Getting into a high gear and standing up on the pedals is not only a good way to wear our your knees, it also wears your chain much more quickly too. Much better to get used to shifting into a lower gear and then spinning the pedals faster but with less force. This is biomechanically more efficient, and is also kinder on the bike’s gear system too.

10. Change into a larger rear sprocket

As above, it’s better to spin the pedals fast than stomp on them slowly. To achieve this you could change into the smallest chainring on the front. But this would mean a higher chain tension, and could easily lead to over-use of the smaller sprockets on the rear. A much better way of achieving exactly the same gear ratio is to change into a larger sprocket on the rear. This means lower chain tension, less wear on the chain and teeth, and more efficient power transfer.